收藏本站
RN -42 -DS
   ?
In this mode, the Bluetooth stack is no longer on-board the module. It is offloaded to the interfacing host processor. The
Bluetooth module is used as a radio, performing the lower level MAC functionalities, while the application stack runs on the
host processor.
Using the module in HCI mode allows designers to implement profiles that are not natively supported on the Bluetooth
module.
NOTE: HCI mode requires a separate firmware build that must be loaded into the module’s flash at the factory. Is not
upgradeable in the field.
Roving Networks offers HCI mode in two hardware interfaces:
?
?
HCI over UART
HCI over USB
HCI over UART
In this mode, the hardware interface between the host processor and the Bluetooth module is the UART. You must
interface the flow control signals between the host processor and the Bluetooth module for the HCI interface to work.
Failure to do so can cause the host processor and the Bluetooth module to become out of sync and break the Bluetooth
link.
HCI over USB
In this mode, the hardware interface between the host processor and the Bluetooth module is the USB. In this
architecture, the Bluetooth module is the USB slave and the host processor is the USB host.
Using the USB interface offers the advantage of a faster data link between the Bluetooth module and the host processor.
With this architecture, it is possible to achieve Bluetooth’s theoretical maximum throughput of 3 Mpbs.
Low Power
To achieve low-power operation, hold the module’s RESET pin low. With RESET = 0 VDC, the module consumes 35 uA of
power. If RESET is left floating or high, the module consumes 3 mA in sleep mode. To obtain the lowest power, the RN-42
should be passive (in slave mode and not trying to make connections).
Using the SPI Bus to Upgrade the Flash Memory
While not required, this bus is very useful for configuring the Bluetooth modules’ advanced parameters. The bus is
required when upgrading the module’s firmware. The typical application schematic shown in Figure 4 shows a 6-pin
header that can be implemented to gain access to this bus. A minimum-mode version might simply use the SPI signals (4
pins) and obtain ground and VCC from elsewhere in the design.
Minimizing Radio Interference
When laying out the carrier board for the RN-42 module, the areas under the antenna and shielding connections should
not have surface traces, ground planes, or exposed vias (see Figure 5). For optimal radio performance, the RN-42
module’s antenna end should protrude at least 5 mm beyond any metal enclosure.
www.rovingnetworks.com
Version 2.2r 4/9/2012
8
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
RP1A090ZPTR MOSFET P-CH 12V 9A MPT6
RP1E050RPTR MOSFET P-CH 30V 5A MPT6
RP1E090RPTR MOSFET P-CH 30V 9A MPT6
RP1E100RPTR MOSFET P-CH 30V 10A MPT6
RPM-012PBT97 PHOTOTRANSISTOR SIDE VIEW SMD
RPM-20PBM PHOTOTRANSISTOR 800NM SIDE VIEW
RPM-22PB PHOTOTRANSISTOR 800NM SIDE VIEW
RPM5340-H14E2A RECEIVER REMOTE 40KHZ SMD SIDE
相关代理商/技术参数
RN42NU-I/RM 功能描述:蓝牙/802.15.1 模块 Class2 Bluetooth mod no ant, HCI over USB RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm
RN-42-SM 功能描述:蓝牙/802.15.1 模块 Class 2 Bluetooth 2.1+EDR Socket Mod RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm
RN42SM-I/RM 功能描述:MODULE BLUETOOTH V2.1+EDR RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件
RN42U-I/RM 功能描述:蓝牙/802.15.1 模块 USB firmware HCI over USB port RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm
RN42XVP-I/RM 功能描述:蓝牙/802.15.1 模块 XV BT Class 2 socket module w/ chip ant RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm
RN42XVP-I/RM 制造商:Microchip Technology Inc 功能描述:XV footprint BT Class 2 socket module w/
RN42XVU-I/RM 功能描述:蓝牙/802.15.1 模块 XV BT Class 2 socket module w/ UFL conn RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm
RN432 制造商:EDSYN 功能描述: